SECO LARM USA Home Security System E 37EV User Guide

E-37EV  
Alarm Pager System  
Manual  
Monitors up to three zones per  
premises or vehicle, plus  
manual paging.  
One positive and two negative  
instant trigger inputs.  
Code-learning receiver learns  
up to three transmitter codes.  
Transmitter can page an  
unlimited number of receivers.  
Colored LEDs or vibrate  
Low-battery indicator.  
Red LED transmission indicator.  
function indicate received page.  
Unattended page indicator.  
NOTE: Antenna required. See page 3 for more details. Antenna not included.  
 
ENFORCER E-37EV Alarm Pager System  
Specifications  
Number of codes  
Over 2 million (factory pre-set)  
Power  
12VDC  
RF output power  
4W max.  
Standby  
Active  
10mA  
1A  
27MHz  
Current drain  
Frequency  
Antenna impedance  
Range  
Dimensions  
Weight  
50 Ω  
Up to 1/2 mile in open air1  
41/8”x31/8”x15/16” (105x79x33 mm)  
5.1-oz (145g)  
1 Actual range may vary depending on the environment, installation, and/or antenna.  
Number of codes  
Power  
Battery life  
Learns up to 3 transmitter codes  
3VDC (2 AAA batteries)2  
Approx. 1 month3  
1mA  
Standby  
Current drain  
Active (Beep)  
Active (Vibrate)  
20mA  
50mA  
Dimensions  
Weight  
3”x21/8”x5/8” (76x54x16 mm)  
1.6-oz (45g) (without battery)  
2 Batteries not included  
3 Based on 5 transmissions/day  
Installation  
Transmitter Installation  
1. Mark locations for drilling the mounting bracket holes. Be careful that the area to be drilled  
is free from wiring, trim, and/or any other obstructions.  
2. Drill holes at the location marks. Position the transmitter where it will be mounted, but do  
not secure immediately.  
3. The transmitter should be permanently mounted only after all connections and tests  
are made.  
NOTES:  
Do not mount the E-37EV transmitter in the engine compartment as this automatically voids  
the warranty.  
Do not power up the transmitter before the antenna connections are made as this may  
damage the transmitter.  
In a building, mount as close to a window as possible.  
In a vehicle, mount under the dashboard or in the glove compartment.  
Antenna Installation (see Connection Diagram on pg. 5)  
The E-37EV can be connected to one of four types of antennas:  
TYPE 1: Strip antenna (A Position)  
1. E-37ANT (optional) can be used in either a building or vehicle.  
2. Connect the male antenna plug into the transmitter jack marked “ANT.”  
3. Place the antenna selection switch in the “A” position.  
4. Do not secure the strip antenna to metal, window defrosters, or existing antennas.  
SECO-LARM U.S.A., Inc.  
3
 
ENFORCER E-37EV Alarm Pager System  
TYPE 2: CB antenna (A Position)  
1. Connect the male antenna plug of an optional CB antenna into the transmitter jack marked  
“ANT.”  
2. Place the antenna selection switch in the “A” position.  
TYPE 3: Standard radio antenna (B Position)  
1. Disconnect the radio antenna lead going into the radio and connect it to the transmitter jack  
marked “ANT.”  
2. Connect the provided male-to-male 18” radio antenna adapter cord between the transmitter  
jack marked “RADIO” and the radio antenna jack.  
3. Place the antenna selection switch in the “B” position.  
TYPE 4: Fully automatic radio antenna (B Position)  
1. Disconnect the radio antenna lead going to the radio and connect to the transmitter jack  
marked “ANT.”  
2. Connect the provided male-to-male 18” radio antenna adapter cord between the transmitter  
jack marked “RADIO” and the radio antenna jack.  
3. Cut the power antenna lead running from the radio to the fully automatic radio antenna.  
4. Connect the lead coming from the power antenna to the long white wire (marked “To power  
antenna sensor wire”).  
5. Connect the lead coming from the radio to the short white wire (marked “To radio switched  
power lead”).  
6. Place the antenna selection switch in the “B” position.  
Wiring  
Red Wire Positive 12VDC power  
Connect the red wire to a constant +12VDC power source.  
Black Wire Ground  
Connect the black wire to the negative terminal of a 12VDC power source.  
Optionally, connect to the frame of the vehicle.  
Purple Wire Positive trigger input  
Connect the purple wire to a burglar or car alarm output that outputs +12V when the alarm is  
triggered (the trigger signals must be at least 1 second long in order to trigger pager.)  
Green Wire Negative trigger input #1  
Connect the green wire to a burglar or car alarm output that outputs ground when the alarm  
is triggered (the trigger signals must be at least 1 second long in order to trigger pager.)  
Blue Wire Negative trigger input #2  
Connect the blue wire to a burglar or car alarm output that outputs ground when the alarm is  
triggered (the trigger signals must be at least 1 second long in order to trigger pager.)  
White Wire Fully automatic radio antenna  
Connect the long white wire (female spade plug) to the power antenna wire coming from the  
power antenna sensor wire.  
Connect the short white wire (male spade plug) to the power antenna wire coming from the  
radio switched power lead.  
Warning: Do not reverse the white wire connections.  
4
SECO-LARM U.S.A., Inc.  
 
ENFORCER E-37EV Alarm Pager System  
Connection Diagram  
E-37ANT  
(Optional)  
Antenna  
Antenna Selection  
Switch  
Antenna (“ANT”)  
LED  
Manual Page  
Radio  
Radio (“RADIO”)  
Cut  
Diode  
IN4004  
White (Short): Radio Switched Power  
White (Long): Power Antenna  
Fuse (2A)  
+12 VDC  
Ground  
Red:  
Constant +12V to Fuse  
Ground  
Black:  
Purple:  
Blue:  
Positive (+) Trigger  
Second Negative (-) Trigger  
First Negative (-) Trigger  
Green:  
Programming  
The receiver must learn the transmitter’s code before it can receive signals from the transmitter.  
The receiver can learn the page codes of up to 3 transmitters.  
1. Turn the receiver OFF. Then press and hold the ON/ /OFF switch and slide it to the ON  
position. Continue holding for 3 seconds until the receiver beeps once.  
2. The PAGE LED will flash GREEN at a steady rate. The ZONE LED will be solid ORANGE.  
This means the receiver is ready to learn the page code of the first transmitter.  
3. Press the manual page button on the transmitter. This will send the page signal to the  
receiver. The receiver will beep twice and the LEDs will turn off to indicate the code has been  
learned. The receiver will beep five times in four minutes if no code is learned.  
4. To learn a second (or third) transmitter, repeat step 1 then press down on the ON/ /OFF  
switch once. The PAGE LED will begin flashing RED for the second transmitter and  
ORANGE for the third transmitter.  
5. Press the manual page button on the second (or third) transmitter. The receiver will beep  
twice and the LEDs will turn off to indicate the page code has been learned. The receiver will  
beep five times in four minutes if no code is learned.  
6. If no additional transmitters need to be learned then move the ON/ /OFF switch back to  
the OFF position.  
Notes:  
The receiver remembers the transmitter codes in EEPROM memory even without  
power for over one year. The receiver does not need to re-learn the transmitter codes  
after battery replacement.  
Only one of each transmitter ID may be learned at a time. For example, if a green  
transmitter is already programmed and a new green transmitter is learned, the previous  
green transmitter will no longer work.  
SECO-LARM U.S.A., Inc.  
5
 
ENFORCER E-37EV Alarm Pager System  
Audible and Visual Signals Chart  
Receiver Display  
Audible / Vibrator  
Transmitter  
Input  
ID  
Page LED Zone LED  
Indicator  
Groups of 9  
Groups of 9  
Groups of 9  
3 groups of 3  
3 groups of 3  
Groups of 9  
Groups of 9  
Groups of 9  
3 groups of 3  
3 groups of 3  
Groups of 9  
Groups of 9  
Groups of 9  
3 groups of 3  
3 groups of 3  
Positive Trigger  
Negative Trigger #1 Green  
Negative Trigger #2 Green  
Manual Page  
Power ON  
Positive Trigger  
Negative Trigger #1 Red  
Negative Trigger #2 Red  
Manual Page  
Power ON  
Positive Trigger  
Negative Trigger #1 Orange  
Negative Trigger #2 Orange  
Green  
Green  
Red  
Green  
Orange  
Green  
None  
Green  
Red  
Orange  
Green  
None  
Green  
Red  
Green  
Green  
Red  
Red  
Red  
Red  
Orange  
Orange  
Orange  
Green  
None  
Manual Page  
Power ON  
Orange  
Orange  
Operation  
Receiver Switch Settings  
: Beeping only  
Trigger Duration  
ON: Vibration only  
OFF: Receiver off  
The transmitter will transmit the page signal for a cycle of about 30 seconds, whether or not  
the triggered zone is reset. If the same zone remains triggered, the transmitter will not start  
a new transmission cycle. However, a new cycle will begin once another un-triggered zone  
is triggered.  
Manual Paging  
When triggered by the manual page button the receiver will beep (or vibrate) continuously  
for 1 minute in 3 groups of 3.  
The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).  
The Zone LED will flash green.  
Press the ON/ /OFF button after 30 seconds to stop the indicator.  
Power-On Paging  
When the transmitter is connected to power the receiver will beep (or vibrate) continuously  
for 1 minute in 3 groups of 3.  
The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).  
The Zone LED will remain blank.  
Press the ON/ /OFF button after 30 seconds to stop the indicator.  
6
SECO-LARM U.S.A., Inc.  
 
ENFORCER E-37EV Alarm Pager System  
Alarm Paging  
When triggered by either the purple (+), green (-), or blue (-) triggers, the receiver will beep  
(or vibrate) continuously for 1 minute in groups of 9.  
The Page LED will indicate which transmitter is sending the signal (Green, Red, or Orange).  
The Zone LED will indicate which trigger was triggered.  
-
-
-
Positive trigger (purple wire) will flash green.  
Negative trigger #1 (green wire) will flash red.  
Negative trigger #2 (blue wire) will flash orange.  
Press the ON/ /OFF button after 30 seconds to stop the indicator.  
Receiver Power-On  
The receiver will beep (or vibrate) once each time the receiver is turned on.  
Unattended Indicator  
The receiver will beep (or vibrate) once every 30 seconds to remind the user that it received  
a page signal from the transmitter.  
Press the ON/ /OFF button to stop the indicator.  
Low-Battery Indicator  
The receiver will beep (or vibrate) twice following power-on if the batteries are low.  
The receiver will also beep (or vibrate) twice every 60 seconds when the batteries are low.  
Viewing the Page Memory  
Scroll back the page signal memory by pressing the ON/ /OFF button repeatedly.  
The receiver remembers the last 6 page signals received.  
Page signals will be shown one by one, beginning with the most recent.  
The receiver will beep once for an alarm page, but will not beep for a manual page.  
The receiver will beep three times to indicate that all signals have been viewed, or that no  
signals are stored.  
Two consecutive page signals carrying the same information are treated as one.  
Turning off the receiver will erase all stored signals.  
Warning  
Ensure that an antenna is connected before connecting power to the unit. Failure to do so may  
damage the transmitter.  
Do not open the receiver or transmitter cases. All adjustments have been made at the factory.  
There are no user serviceable parts inside.  
Holes marked 1, 2, and 3 on the transmitter case are factory set. Do not make any  
adjustments in these holes.  
Use only AAA size 1.5V alkaline batteries for the receiver.  
SECO-LARM U.S.A., Inc.  
7
 
ENFORCER E-37EV Alarm Pager System  
Troubleshooting  
No page signal  
Check that all connections are securely made  
Check that the antenna is securely fastened  
Check the receiver batteries  
Possibly out of range Move antenna to better position  
Make sure the antenna selection switch is in the correct  
position  
Check that the transmitter has been properly learned  
Receiver only outputting vibrate/beep  
Check that the receiver is in the correct alert mode  
Also Available from SECO-LARM  
E-37RV Vibrating Transmitter  
E-37ANT Strip Antenna  
FCC COMPLIANCE STATEMENT  
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device,  
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference  
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio  
frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to  
radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case  
the user will be required to correct the interference at his or her own expense.  
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal  
service for a period of one (1) year from the date of sale to the original customer. SECO-LARM’s obligation is limited to the  
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.  
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair  
or alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such  
equipment is not operating properly as a result of causes other than defects in material and workmanship.  
The sole obligation of SECO-LARM and the purchaser’s exclusive remedy shall be limited to replacement or repair only, at  
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal  
or property damages of any kind to the purchaser or anyone else.  
NOTICE  
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM  
policy is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change  
specifications without notice. SECO-LARM is also not responsible for misprints or typographical errors.  
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or  
in part, without the written permission of SECO-LARM.  
SECO-LARM U.S.A., Inc.  
16842 Millikan Avenue, Irvine, CA 92606  
Tel: 800-662-0800 / 949-261-2999  
PIHKK2  
MiE-37EV_1209.docx  
8
SECO-LARM U.S.A., Inc.  
 

PYLE Audio Stereo System PLCD20CH User Guide
Radio Shack Motorized Toy Car 60 4360 User Guide
Radio Shack Surge Protector 61 2429 User Guide
Rinnai Water Heater REU VA3237FFU User Guide
Rockford Fosgate Car Speaker FFC65 User Guide
Rosewill Mouse RM 5000L User Guide
Samsung Digital Camera AD68 04852A User Guide
Samsung DVD Player CHT 350 User Guide
Samsung GPS Receiver N 35861 User Guide
Samsung Washer SW57APP User Guide