SECO LARM USA Security Camera EV 1726 NKGQ User Guide

DNR / DWDR / IR  
NVD Bullet Camera  
with 4-Axis Mounting Arm  
Installation Manual  
3 Cameras in 1:  
EV-1726-NKGQ (NTSC)  
2.8~12mm  
EV-1726-PKGQ (PAL)  
EV-1726-NWGQ (NTSC)  
EV-1726-PWGQ (PAL)  
6~50mm  
1/3” Sony Super HAD II CCD  
12VDC/24VAC  
OSD with service monitor port  
600 TV lines  
NVD Bullet Cameras have an ultra-low Lux rating of 0.00006 allowing the  
camera to see in almost total darkness.  
Note: Products with model numbers that end with “Q” or that have a round green “Q” sticker are RoHS compliant.  
 
ENFORCER DNR / DWDR / IR NVD Bullet Camera with 4-Axis Mounting Arm  
Overview:  
Mounting screw  
Sunshield  
Hex screw  
Rubber grommet  
BNC connector  
Mounting plate  
4-Axis mounting arm  
Mounting base  
Service  
monitor port  
Zoom  
Focus  
Connect  
service monitor  
port connector  
DC Jack DC plug with  
terminal block  
OSD joystick  
Important:  
Do not cut DC jack or BNC  
connector as warranty will be voided.  
Before Starting:  
1. Please read this manual carefully and keep it for  
future reference.  
2. Use the camera within given temperature and  
electrical limits.  
3. Do not aim the LEDs directly at the eyes when the  
LEDs are on.  
5. Do not mount the camera in areas exposed to  
radiation, strong magnetic fields, or strong  
electrical signals.  
6. Do not open or disassemble the camera. There are  
no field-serviceable parts inside.  
7. Do not drop the camera or subject it to  
4. Do not point the camera at the sun. Heat could  
strong vibrations.  
damage the camera, even when not in use.  
Installation:  
1. Run a 12VDC or 24VAC power supply wire and a  
video cable with a male BNC connector through the  
wall to where the camera is to be mounted.  
2. Temporarily connect the camera to the power  
supply. Do not cut the DC jack or the female BNC  
connector as the warranty will be voided. If  
needed, use the included SECO-LARM DC plug  
with terminal block.  
6. Mount the mounting plate and rubber grommet to  
the wall or ceiling using the four included mounting  
screws. If the wall is made of drywall, brick, or  
similar material, it may be necessary to use screw  
anchors (not included).  
7. Mount the camera base to the mounting plate using  
the four included hex screws.  
8. Adjust the camera angle. See “4-Axis Mounting  
Arm” on page 2.  
3. Connect the included service monitor port connector  
to the service monitor port.  
4. Connect the service monitor port connector’s BNC to  
a test monitor.  
5. While watching the monitor, hold the camera against  
the wall or ceiling by hand where it is to be mounted,  
then turn the camera until it is certain that this  
mounting location is correct. Use a pencil to mark  
the location of the four screw holes in the  
mounting plate.  
9. Adjust zoom and focus by moving the zoom and  
focus knobs on the side of the camera. Then use  
the OSD control joystick to adjust camera settings.  
(See OSD manual).  
10. Disconnect the power supply and service  
monitor connector.  
11. Put the sunshield on the camera.  
12. Do a final test of the video camera and monitor.  
SECO-LARM U.S.A., Inc.  
3
 
ENFORCER DNR / DWDR / IR NVD Bullet Camera with 4-Axis Mounting Arm  
Troubleshooting  
Check that the camera is powered up.  
Check that the power supply’s polarity is correct.  
The screen is blank.  
Check that the monitor is powered up.  
Check that the video cable connecting the camera to the  
monitor is connected properly.  
Clean the lens using a soft, clean cloth.  
Check that the light source is adequate.  
The screen image is dim.  
Adjust the monitor’s contrast knob.  
Change the position of the camera.  
The screen image has poor contrast.  
The screen image flickers.  
Change the position of the camera.  
The screen image is distorted.  
Change the position of the camera.  
The camera case is hot.  
IR LEDs do not turn on.  
IMPORTANT  
Check that the correct power supply is in use.  
Check that the correct power supply is in use.  
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and  
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this  
product in violation of any current laws or statutes.  
WARNING  
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not  
open the case of this device, as there are no field-serviceable components inside.  
FCC COMPLIANCE STATEMENT  
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant  
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to  
correct the interference at his own expense.  
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service  
for a period of three (3) years from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the  
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.  
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair, or  
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such  
equipment is not operating properly as a result of causes other than defects in material and workmanship.  
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at  
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or  
property damages of any kind to the purchaser or anyone else.  
NOTICE  
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy  
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications  
without notice. SECO-LARM is also not responsible for misprints or typographical errors.  
Copyright © 2011 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in  
part, without the written permission of SECO-LARM.  
®
U.S.A., Inc.  
16842 Millikan Avenue, Irvine, CA 92606  
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: [email protected]  
PIKHR1  
MiEV-1726-xxGQ_1110.docx  
Made in Korea  
4
Download from Www.Somanuals.com. All Manuals SearSchEACndOD-oLwAnlRoaMd. U.S.A., Inc.  

Radio Shack Car Speaker 40 215 User Guide
Radio Shack Cordless Telephone ET 537 User Guide
Roberts Gorden Heating System HE15ST User Guide
RocketFish Computer Drive RF PHD25 User Guide
Rowenta Iron Power Press User Guide
RuggedCom Switch RS900GP User Guide
Sakar Digital Camera 84379 User Guide
Samsung Cell Phone GH68 05578A User Guide
Samsung Telephone MM A880 User Guide
Sanyo Flat Panel Television DP50842 User Guide