SECO LARM USA Security Camera EV 1826 NKGQ User Guide

EV-1826-NKGQ (NTSC)  
EV-1826-PKGQ (PAL)  
84-IR LED Bullet Cameras  
Manual  
1
/3” Sony Super HAD II CCD  
2.8~12mm Varifocal lens  
Weatherproof (IP66)  
Zeta Series  
OSD Controller  
Model No.  
EV-18C  
OSD functions accessible with  
optional OSD controller (EV-18C)  
Optimized to produce clear  
images at night  
Cables concealed in bracket  
12VDC operation  
Use to access the OSD  
(On-Screen Display)  
functions for  
compatible cameras  
without having to be  
near the camera.  
Optional single-gang mounting plate  
and round junction box available  
Not included.  
For more information, please see the EV-18C manual.  
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.  
 
ENFORCER 84-IR LED Bullet Cameras  
Dimensions:  
45/8”  
(118mm)  
45/16  
(109mm)  
101/4” (260mm)  
1013  
/16” (275mm)  
45/8” (116mm)  
Overview:  
Mounting base  
Sunshield  
Sunshield  
screw  
Surface mount  
Female BNC connector  
Mounting arm  
knock-out  
Remove with a pair of  
pliers  
adjustment screw  
DC Plug with  
terminal block  
Mounting  
arm  
Adjustment  
screw  
Camera angle  
adjustment screw  
DC jack  
Zoom  
Focus  
Adjustment nut  
Before Starting:  
1. Please read this manual carefully and keep it for  
future reference.  
2. Use the camera within given temperature and  
electrical limits.  
3. Do not aim the LED light directly at the eyes when the  
LEDs are on.  
4. Do not point the camera at the sun. Heat could damage  
the camera, even when not in use.  
5. Do not mount the camera in areas exposed to  
radiation, strong magnetic fields, or strong electrical  
signals.  
6. Do not open or disassemble the camera. There are  
no field serviceable parts inside.  
7. Do not drop the camera or subject it to strong  
vibrations.  
Installation:  
1. Run a 12VDC power supply wire and a video cable  
with a male BNC connector through the wall to where  
the camera is to be mounted.  
4. Disconnect the 12VDC power supply and video cable.  
5. Mount the bracket to the wall using the four included  
mounting screws.  
2. Temporarily connect the camera to the 12VDC power  
supply. Do not cut the DC jack or female BNC plug  
as warranty will be voided. If needed, use the  
included SECO-LARM DC plug with  
6. If mounting to the EV-11LR or EV-11LS, see instructions  
on page 2.  
7. Reconnect the 12VDC power supply and video cable.  
Turn the monitor on and make sure the camera is  
sending the proper video signal.  
terminal block.  
3. Temporarily connect the camera’s female BNC jack to  
the video cable’s male BNC plug. While watching the  
monitor, hold the camera bracket by hand against the  
wall where it is to be mounted, then twist the camera  
until it is certain that this mounting location is correct.  
Use a pencil to mark the location of the four screw  
holes in the bracket.  
8. To adjust the camera angle, loosen and tighten the  
adjustment nut, or loosen and tighten either of the two  
screws on the mounting arm. Adjust until the desired  
scene is displayed.  
9. Adjust the zoom and focus using the included hex  
wrench.  
10. Do a final test of the video camera and monitor.  
SECO-LARM U.S.A., Inc.  
3
 
ENFORCER 84-IR LED Bullet Cameras  
Troubleshooting:  
Check that the camera is powered up.  
Check that the power supply’s polarity is correct.  
Check that the monitor is powered up.  
Check that the video cable connecting the camera to the  
monitor is connected properly.  
The screen is blank.  
Clean the lens using a soft, clean, dry, and lint-free cloth.  
Check that the light source is adequate.  
The screen image is dim.  
Adjust the monitor’s contrast knob.  
Change the position of the camera.  
The screen image has poor contrast.  
The screen image flickers.  
The screen image is distorted.  
The camera case is hot.  
IR LEDs do not turn on.  
Change the position of the camera.  
Change the position of the camera.  
Check that the correct power supply is in use.  
Check that the correct power supply is in use.  
IMPORTANT  
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and  
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this  
product in violation of any current laws or statutes.  
WARNING  
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not  
open the case of this device, as there are no field serviceable components inside.  
FCC COMPLIANCE STATEMENT  
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant  
to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy  
and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to  
correct the interference at his or her own expense.  
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service  
for a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the  
repair or replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.  
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or  
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such  
equipment is not operating properly as a result of causes other than defects in material and workmanship.  
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at  
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or  
property damages of any kind to the purchaser or anyone else.  
NOTICE  
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy  
is one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications  
without notice. SECO-LARM is also not responsible for misprints or typographical errors.  
Copyright © 2012 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in  
part, without the written permission of SECO-LARM.  
SECO-LARM U.S.A., Inc.  
16842 Millikan Avenue, Irvine, CA 92606  
PICSN5  
MiEV-1826-xKGQ_1206.docx  
Tel: 800-662-0800 / 949-261-2999 Fax: 949-261-7326 E-mail: [email protected]  
4
Download from Www.Somanuals.com. All Manuals SearSchEACndOD-oLwAnlRoaMd. U.S.A., Inc.  

Radio Shack Stereo Receiver HTX 400 User Guide
RBH Sound Speaker WM 24 User Guide
RCA Washer YVXR1040VWW User Guide
RocketFish Indoor Furnishings RF TVMLPT03 User Guide
RocketFish Video Gaming Accessories RF GXBX011 User Guide
Saeco Coffee Makers Network Hardware SUP021R User Guide
Samsung Air Conditioner AS09F User Guide
Samsung Blu ray Player AK68 01859A User Guide
Samsung Telescope DMR57 User Guide
Sears Power Roller PRC 241 BH User Guide