SECO LARM USA Security Camera EV 2660 NKBAQ User Guide

High Resolution Indoor  
Dome Cameras  
Manual  
EV-2661-NKBQ  
EV-2660-NKBQ  
EV-2660-NKBAQ  
Features  
EV-2660-NKBQ  
EV-2660-NKBAQ  
EV-2661-NKBQ  
550 TV Lines  
3-Axis Gimbal Bracket  
2.8~10.5mm Varifocal Lens  
Dual Voltage  
True Day & Night  
36 IR LEDs  
Note: Model numbers that end with “Q” or that have a round green “Q” sticker signify RoHS-compliant products.  
 
SECO-LARM High Resolution Indoor Dome Cameras  
Installation  
EV-2660-NKBQ or EV-2660-NKBAQ shown. Installation is the same for all three models.  
Mounting surface  
Female BNC connector  
(connect to video device)  
Base  
DC plug with terminal block  
Mounting screw  
Zoom  
DC Jack  
(connect to power)  
Important: Do not cut DC jack or BNC connector as  
warranty will be voided.  
Service Monitor Port  
Service monitor adapter  
Connect to service monitor  
Focus  
at the installation site  
Connects to Service  
Dome  
Monitor Port  
Before Starting  
1. This product was designed for indoor use only. Do not  
mount the CCTV camera where it is exposed to rain or  
other moisture, or in humid or dusty places.  
2. Do not point the CCTV camera at the sun. Heat could  
damage the camera, even when not in use.  
3. Do not mount the CCTV camera in areas exposed to  
radiation, strong magnetic fields, or strong electrical  
signals.*  
4. Do not open or disassemble the camera. There are no  
user serviceable parts inside.  
5. Do not drop the camera or subject it to strong vibrations.  
Note: Many video monitors produce strong  
electromagnetic fields close to the display CRT,  
especially when the monitor is turned on or during de-  
Gaussing, which occurs automatically with many  
monitors when the monitor is turned on.  
Installation  
1. Remove the dome by twisting counterclockwise. Be  
careful not to scratch the dome. Do not touch any of  
the components inside the dome.  
6. Run a hidden cable from the power supply to the  
mounting location.  
7. Connect the two cables to the dome camera. Do not  
cut any wires, as warranty will be voided. If needed,  
use the included DC plug with terminal block.  
8. Mount the base to the ceiling at the selected location.  
9. Use the 3-axis gimbal to adjust the angle of the camera.  
(See opposite page for further instructions.)  
10. Make any necessary adjustments to the Zoom and  
Focus by pulling the respective levers out and turning  
them clockwise or counterclockwise.  
11. Replace the dome, taking care not to touch the camera  
or scratch the dome.  
12. Test the camera again under the exact lighting  
conditions under which it is expected to be used.  
2. Temporarily connect the camera to the video monitor via  
the video cable. If a service monitor is available, use the  
included service monitor adapter.  
3. Temporarily connect the camera to a 12VDC  
power source. (24VAC may be connected for  
EV-2660-NKBAQ and EV-2661-NKBQ).  
4. Hold the base of the dome camera with your hand against  
the ceiling, and try various locations and angles while  
watching the video monitor to find the location which  
offers the best protection. Mark that location  
with a pencil.  
5. Run a hidden, permanent video cable from the monitor to  
the mounting location.  
SECO-LARM U.S.A., Inc.  
3
 
SECO-LARM High Resolution Indoor Dome Cameras  
Troubleshooting:  
Check that the camera is powered up.  
Check that the power supply’s polarity is correct.  
Check that the monitor is powered up.  
The screen is blank.  
Check that the video cable connecting the camera to the  
monitor is connected properly.  
Clean the lens using a soft, clean cloth.  
Check that the light source is adequate.  
The screen image is dim  
The screen image has poor contrast.  
The screen image flickers.  
Change the position of the camera.  
Change the position of the camera.  
The screen image is distorted.  
Change the position of the camera.  
The camera case is hot.  
IR LEDs do not turn on.  
IMPORTANT  
Check that the correct power supply is in use.  
Check that the correct power supply is in use.  
Users and installers of this product are responsible for ensuring this product complies with all national, state, and local laws and  
statutes related to monitoring and recording audio and video signals. SECO-LARM will not be held responsible for the use of this  
product in violation of any current laws or statutes.  
WARNING  
Stop using the camera if you see a malfunction such as smoke or unusual heat, as it could cause fire or electric shock. Do not open  
the case of this device, as there are no field-serviceable components inside.  
FCC COMPLIANCE STATEMENT  
Information to the user: This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to  
part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the  
equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if  
not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.  
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to  
correct the interference at his or her own expense.  
WARRANTY: This SECO-LARM product is warranted against defects in material and workmanship while used in normal service for  
a period of one (1) year from the date of sale to the original consumer customer. SECO-LARM’s obligation is limited to the repair or  
replacement of any defective part if the unit is returned, transportation prepaid, to SECO-LARM.  
This Warranty is void if damage is caused by or attributed to acts of God, physical or electrical misuse or abuse, neglect, repair or  
alteration, improper or abnormal usage, or faulty installation, or if for any other reason SECO-LARM determines that such equipment  
is not operating properly as a result of causes other than defects in material and workmanship.  
The sole obligation of SECO-LARM, and the purchaser’s exclusive remedy, shall be limited to replacement or repair only, at  
SECO-LARM’s option. In no event shall SECO-LARM be liable for any special, collateral, incidental, or consequential personal or  
property damages of any kind to the purchaser or anyone else.  
NOTICE  
The information and specifications printed in this manual are current at the time of publication. However, the SECO-LARM policy is  
one of continual development and improvement. For this reason, SECO-LARM reserves the right to change specifications without  
notice. SECO-LARM is also not responsible for misprints or typographical errors.  
Copyright © 2010 SECO-LARM U.S.A., Inc. All rights reserved. This material may not be reproduced or copied, in whole or in part,  
without the written permission of SECO-LARM.  
SECO-LARM U.S.A., Inc.  
16842 Millikan Avenue, Irvine, CA 92606  
Tel: 800-662-0800 / 949-261-2999  
PIKPR1  
MiEV-266x-NKB_1008.docx  
4
SECO-LARM U.S.A., Inc.  
 

Radio Shack Radar Detector 22 1670 User Guide
Radio Shack Thermometer Thermometer User Guide
Radio Shack Weather Radio Pro 2035 User Guide
RCA Clock Radio RC40 User Guide
Reebok Fitness Home Gym RBBE07871 User Guide
Roland Electronic Keyboard AT 500 User Guide
Roper Range FGP335B User Guide
Samsung All in One Printer SLM3320ND User Guide
Samsung Headphones WEP490 User Guide
SanDisk Computer Drive CompactFlash 5000 User Guide